Coolant aspects – machining with coolant

In some cases it may be an environmental and cost perspective benefit to machine without coolant (dry machining). However many applications require machining with coolant for tolerance, surface quality and machinability. If coolant is required, it should be optimized to maximize its true potential.

High pressure coolant

Nearly all machines offer a standard high pressure coolant capability of 70/80 bars (1015/1160 psi). Some machines can even deliver higher coolant pressures, up to 150 bar (2176 psi), for demanding operations and materials.

The benefits can be great for both turning and drilling operations, however it is worth noting:

• Benefits will only be achieved with tools developed for precision coolant applications, i.e. drills with through coolant and turning tools with targeted jets
• The required coolant pressure to break the chip for turning tools depends on the nozzle delivery design, material being machined and the depth of cut and feed
• The coolant flow required depends on the pressure and the total coolant delivery area of the tool channels

Select the right tools and pump (pressure and flow) for each application. A correctly applied high pressure coolant system will provide quick payback due to increased machine utilization and increased metal cutting efficiency.

Benefits when machining with coolant

When combining high pressure with optimized cutting tools and quick change you will get a great amount of benefits.

Chip control

Eliminate two of the biggest production time killers when the red light is on.

• Machine stoppages: Long chips gathering around the tool or component
• Service: Chips "bailed" in the chip conveyor takes the machine out of action for hours or days

Chip evacuation in drilling

Internal through coolant helps with chip evacuation, preventing chip jamming in the flute.

Fixed nozzle position

No need for operator settings which means increased machine utilization.

Increased cutting speed

Gives higher metal cutting efficiency.

Precision coolant with high pressure

High pressure in the machine together with modern turning tools that features nozzles can produce a high velocity coolant jet. The coolant jets are directed towards the cutting zone on the insert rake side and will act like a hydraulic wedge to lift the chip. This shortens the contact length between the insert and the material which help to reduce cutting forces, lower the temperature and improve chip control.

High pressure coolant principles

Pressure (p): Force per unit area

• Pascal, N/m
• Bar (1 bar = 0.1 MPa)
• psi, pounds/in² (1 bar = 14.5 psi)

Low rate (v): Volume displaced per time unit, litre/min (gallon/min)

Velocity (w): Speed that the fluid moves through a tube, m/s (ft/s)

Reducing the delivery area increases the velocity of the jet and at the same time reduces the flow for a given pressure. Utilizing optimized small diameter nozzles produces an accurate laminar jet.

Flow velocity w₁

Flow velocity w₁

w₂>>w₁

In the diagram below the volume flow required is shown in relationship to the nozzle diameter for a fixed 80 bar (1160 psi) pressure. By using small diameter nozzles, high velocity jets can be produced and at the same time reduce the flow and energy required compared to traditional coolant systems.

X-axis: Number of nozzles

Y-axis: Flow, litres/min

Pump requirements

The pump requirements to apply high pressure coolant successfully are pressure and flow.

Pressure

The pressure requirement to break the chip varies depending on the material and the cutting parameters. 80 bars (1160 psi) is adequate for most applications. Higher pressures, up to 150 bar (2176 psi), are used for hard-to-break chips in materials such as Inconel and super duplex

Flow

The flow required is driven by the number and diameter of coolant outlets.

• Use a 20 microns filter
• Turning: If using tool holders with three 1 mm (0.039 inch) coolant nozzles, the flow requirement is 20 litres/min per tool position. However, it is important to consider the number of tools being run with coolant at the same time (number of tools × 20 litres/min). Because of the size of the machine, a large tank is needed to provide time for circulation
• Drilling: The coolant hole diameters in the drill increase with the drill diameter meaning that a higher flow rate is needed for larger diameter drills. The goal is volume of flow, not pressure. A variable pressure pump is recommended and to use lower pressures with larger diameter drills

Coolant connection

One of the big benefits of using high pressure coolant systems is the reduction of coolant pipe setting. With external pipes it normally takes two to three attempts to get the coolant position right. Poor chip control often knocks the pipe and re-setting is quite a regular occurrence meaning an inconsistent process and the red light on.

When using tool holders with precision nozzles, the coolant delivery from the tool to the cutting edge is fixed but the coolant still needs to be connected to the tool holder. Pipe connections can be used into a shank holder, however, this will increase the set-up time every time the tool is changed and also interference and a chip trap is created.

The best solution is to use quick change, a plug and play solution. The coolant is permanently plumbed into the tool holder clamping unit. With these solutions the adoption of machining with high pressure coolant has an additional benefit of reduced set-up times on top of chip control and increased metal cutting efficiency.

Coolant connection in turning centres and lathes

With Coromant Capto® clamping units, the coolant is plumbed through the turret allowing quick change and pre-measuring outside the machine. Clamping units are available for all lathe styles (turning centers, vertical lathes and flatbed lathes) and new clamping sets allow pressure for 200 bars (2900 psi).

Coolant connection in sliding head machines

Coolant delivery on a sliding head machine varies considerably compared to a turning center. Synthetic oil is used rather than emulsion to support the sliding guide way construction and the oil is delivered to all tools simultaneously regardless of which tool is in cut.

Although most machines get delivered with high pressure pumps, without optimized tooling the coolant delivery area (diameter of coolant outlet × number of outlets) will probably be too large for the flow capability of the pump so maximum pressure will not be achieved.

It is important to reduce the delivery area by:

1. Using tools with internal coolant supply and block off external supply to these tools
2. Optimize the coolant delivery area to minimize the flow required

QS™ holding system includes tool holders which have the coolant plumbed into the stop which is permanently mounted in the machine. A coolant tube in the back of the QS™ tool holder ensures the coolant is channeled straight out to the nozzles at the same time the tool is mounted.

The nozzles are 1 mm (0.039 inch) in diameter ensuring an accurate jet to assist chip control and at the same time keep the flow requirement to a minimum.

Sleeves for quick set-up of boring bars

High pressure metallic sealed sleeves, such as EasyFix, provide quick set-up of cylindrical shank boring bars. The sprung loaded ball locates the groove in the boring bar to find the center position in seconds.